MSD Red Digital 6AL Ignition Control Module & 2 Step Rev Controller 6425 8732
MSD Red Digital 6AL Ignition Control Module & 2 Step Rev Controller 6425 8732. Red Digital 6AL Ignition Control Module & 2 Step Rev Controller. Part #: 6425 Built-In Adjustable Rev-Limit Control Compatible with 4, 6, or 8 Cylinder Engines – Built-in LED for System Checks. The MSD 6AL Ignition Control set the standards that other ignitions strive to reach. In fact, you’ll find ignitions from other companies that carry the 6AL name (and in some cases, the same part number). MSD raised the bar even higher with the revised Digital 6AL Ignition Control! The wiring of the Digital 6AL is routed out one end of the unit through a sealed and locking connector. This eases installation and keeps your wiring looking neat and clean. The rev-limiter of the 6AL is located right on top of the housing for easy access to the two rotary dials to set the limit in 100 rpm increments. Inside the Digital 6AL, you’ll find a microprocessor that monitors and controls every firing and rev limit. The circuits are updated with efficient components that help the ignition produce more power while drawing less current! In fact, the Digital 6AL delivers over 530 volts to the coil with up to 135mJ of spark energy for every firing! Increased output combined with MSD’s proven multiple spark series is a win-win situation! The Digital 6AL is supplied with the wiring harness and the components you’ll need for installation. The 6AL is also supplied with vibration mounts. Both ignitions are compatible on 4, 6, or 8-cylinder engines with 12-volt, negative ground electrical systems. They’ll accept trigger inputs from breaker points, amplifiers, and magnetic pickups. High output with 530 volts and 135mJ of spark energy. Efficient components use less current to produce more power. Set an rpm limit with two rotary dials in 100 rpm increments. Built-in LED for system checks. All wires exit through a locked, sealed connector. Compatible with 4, 6 or 8-cylinder engines. 7 Amp per 1,000 RPM. Primary Voltage: 520-540 Volts. Product Type: Digital 6AL Ignition Control Box. RPM Range: 11,000 RPM. Secondary Voltage: 45,000 Volts. Spark Energy: 135-145 mJ per spark. Voltage Required: 12-15 Volts, 7 Volt Start. Weight and Size: 1.7 lbs. 8″L x 4″W x 1.825H. This part is legal for sale and use on Emissions Controlled Vehicles, in all 50 states, when used in accordance with the manufacturers application guide because it has a California Air Resources Board (CARB) Executive Order (EO) number. The following vehicles are considered Emissions Controlled Vehicles: 1966 and newer U. Manufactured California Certified vehicles 1968 and newer U. Manufactured Federally Certified vehicles 1968 and newer Foreign manufactured vehicle. Part #: 8732 MSD 2-STEP REV CONTROL – FOR DIGITAL 6AL PN 6425 or 64253 Only. Since the new Digital 6AL Ignition uses rotary dials to adjust the rev limiter, their engineers were tasked with developing a 2-Step Rev Control that could be added to give racers the ability to switch to a low rpm limit to use on the starting line. There are two easy to read rotary dials that let you set the launch rpm in 100 rpm increments. There is an activation wire that connects to the transbrake, a clutch switch or to the line-lock to activate the low rpm limit. When that switch is released, the low rpm limit is turned off and the car launches hard! The 2-Step is also digitally controlled and connects to the Digital 6AL’s gray tach output wire. For use with Digital 6AL PN 6425 or 64253 only. Product Type: RPM Control. This part is legal for sale or use on Racing Use Only Vehicles The following vehicles are considered Racing Use Only Vehicles: Racing Use Only Vehicles are vehicles that are used exclusively for competition that are not registered and that may never be used on the street. WARNING: It is against the law to install this part on an Emissions Controlled Vehicle. This part is universal.
Comments are closed.